Controlled-products-systems-group 7300ETL-IL Manuel d'utilisateur

Model 7300INSTALLATION MANUALAPOLLO Gate Operators, Inc.Model 7300ETL-IL08/18/09Residential & Heavy Duty Commercial Slide Gate Operator

10CHAIN & CHAIN BOLT INSTALLATIONSTEP 1. Position the gate so that the operator is in the center of thegate. Connect chain bolt to the chain brack

11Step 1. Press LED Enable once on theright side of the circuit board. The STOPLED should illuminate. This is a standardcondition.Internal Limit Adjus

12Left or Right Hand OperationoperatorGate in closed positionoperatorGate in closed positionWiring InstructionsSTEP 1. Determine which direction the g

13QUICK RELEASE OPERATIONEngagedEngagedPull & turn 1/2 inch to disengage

14STEP 7 Programming Current SensingThe 835/836 control boards incorporate a safety feature that will put the op-erator into a hard shutdown mode if t

15APOLLO Gate Operators, Inc.835/836 Gate Control BoardFirmware Version 31 and upRev F07/15/2005

16PROGRAMMING INSTRUCTIONSOnce the operator is installed or if the control board is replaced, you will need to programthe control board for proper cur

17LED Enable & LearnMode Push ButtonOptional Device InputsStop Circuit JumperFire & ETL InputsEmergency BypassReverse Battery PolarityIndicato

18Board Actuator Function CablePin 1 Orange Open LimitPin 2 White Close LimitPin 3 Black Motor (positive on open, negative on close)Pin 4 Red Motor (n

19AdjustmentsPush ButtonsTIMER TO CLOSE Adjusts time before gate automatically closesAdjustable 5 to 70 seconds.DUAL GATE DELAY Adjusts delay between

2CONTENTSIMPORTANT SAFETY INSTRUCTIONS ... 3Applications ...

20Program SwitchesOFF ON1 TIMER TO CLOSE Gate does not automatically close. Gate automatically closes.2 TIMER TO CLOSE OPT. Gate automatically close

21GND Supplied Battery GroundINP Activate Gate (Push button activation when momentarily shorted to ground)12V Supplied Battery Voltage (Protected with

22APOLLO Gate Operators, Inc.911 SirenMount siren in an area that will produce maximum performance (additional wire may be required).Connect the red w

23APOLLO Gate Operators RECEIVER OPTIONSDo not confuse the receiver code switches with the red program switches on the gate control board.Never set al

24The Apollo 835/836 board is the standard board in all ETL compliant Apollo Gate Opera-tors. Single gate systems use the 835 board (disting

255. Activating the system: A momentary connection between activation inputs and ground(GND) is how the system is activated. At the upper left and bot

26LIMITED TWO-YEAR WARRANTYApollo Gate Operators are warranted against defects for a period of24 months from the date of purchase, providing recommen

3WARNING - To reduce the risk of injury or death: READ AND FOLLOW ALL INSTRUCTIONS. Installation should be performed by a professional installer.

4APPLICATIONSThe Apollo Model 7300ETL Slide Gate Operator is designed to handle a slide gateup to 32 feet in total length (30 foot gate with 3 foot ta

5PRE-INSTALLATION CHECKLISTThe following checklist should be used before beginning installation:• Verify that the proper operator has been selected fo

6PARTS IDENTIFICATIONChain Brackets (2)#40 Roller Chain (35 feet)Tie Wraps (4 each)Master Chain Links (2 each)Operator5/16 Washers, LockNuts, & Nu

7PAD INSTALLATIONPad LocationDrivewayDirection of Opening12” 24”24”5”Fig. AFig. BConduit requirements should be considered in the planning stage. If e

8OPERATOR INSTALLATIONChain path(Make surethe chainpath clearsall posts andobstacles).TOP VIEWFour 1/2” anchor bolts (not supplied) arerecommended to

9CHAIN BRACKET INSTALLATIONSTEP 1. Assemble chain bracket with 5/16” U-bolt & hardware to each end of the gate as shown. Do not tighten at this ti