Controlled-products-systems-group 1042011 Manuel d'utilisateur télécharger pdf (Page 2)

Both the installer and the owner and/or operator of this

system need to read and understand this installation

manual and the safety instructions supplied with other

components of the gate system. This information

should be retained by the owner and/or operator of the

gate.

WARNING! To reduce the risk of injury or death

1. READ AND FOLLOW ALL

INSTRUCTIONS.

2. Never let children operate or play with gate

controls. Keep the remote control away from

children.

3. Always keep people and objects away from

the gate. NO ONE SHOULD CROSS THE

PATH OF THE MOVING GATE.

4. Test the gate operator monthly. The gate

MUST reverse on contact with a rigid object

or stop when an object activates the non-

contact sensors. After adjusting the force or

the limit of travel, retest the gate operator.

Failure to adjust and retest the gate operator

properly can increase the risk of injury or

death.

5. Use the emergency release only when the

gate is not moving.

6. KEEP GATES PROPERLY MAINTAINED. Read

the owner’s manual. Have a qualified service

person make repairs to gate hardware.

7. The entrance is for vehicles only. Pedestrians

must use separate entrance.

8. SAVE THESE INSTRUCTIONS.

When installing photo-beams with this unit two things

need to be considered.

1. Care should be exercised to reduce the risk of

nuisance tripping, such as when a vehicle, trips

the sensor while the gate is in motion.

2. One or more photobeams shall be located

where the risk of entrapment exists, such as

the perimeter reachable by the moving gate

leaf.

GATE DESIGN

1. A gate is a potential traffic hazard, so it is im-

portant that you locate the gate far enough away

from the road to eliminate the potential of traffic

getting backed up. This distance is affected by the

size of the gate, how often it is used, and how fast

the gate operates.

2. The operator you choose to install on your gate

must be designed for the type and size of your

gate and for the frequency with which you use the

operator.

3. Your gate must be properly installed and must work

freely in both directions before the automatic

operator is installed.

4. An automatic operator should be installed on the

inside of the property/fence line. Do not install the

operator on the public side of the property/fence

line.

5. Pedestrians should not use a vehicular gate system.

Prevent such inappropriate use by installing

separate gates for pedestrians.

6. Exposed, reachable pinch points on a gate are

potentially hazardous and must be eliminated or

guarded.

7. Outward swinging gates with automatic operators

should not open into a public area.

8. The operating controls for an automatic gate must

be secured to prevent the unauthorized use of those

controls.

9. The controls for an automatic gate should be

located far enough from the gate so that a user

cannot accidentally touch the gate when operating

the controls.

10. An automatic gate operator should not be installed

on a gate if people can reach or extend their arms

or legs through the gate. Such gates should be

guarded or screened to prevent such access.

11. Be Sure to locate any switches that will activate the

gates movement at least 10ft. From the gate(s)

INSTALLATION

1. If you have any question about the safety of the

gate operating system, do not install this operator.

Consult the operator manufacturer.

2. The condition of the gate structure itself directly

affects the reliability and safety of the gate

operator.

3. Only qualified personnel should install this

equipment. Failure to meet this requirement could

cause severe injury and/or death, for which the

manufacturer cannot be held responsible.

4. The installer must provide a main power switch that

meets all applicable safety regulations.

5. Clearly indicate on the gate with the 2 warning signs

that are included (visible from either side of the

gate).

6. It is extremely unsafe to compensate for a damaged

gate by increasing hydraulic pressure.

7. Devices such as reversing edges and photobeams

must be installed to provide better protection for

personal property and pedestrians. Install reversing

devices that are appropriate to the gate design and

gate application.

8. Before applying electrical power, be sure that the

voltage requirements of the equipment correspond

IMPORTANT SAFETY INFORMATION

February, 2009

400 Operator And

455 D Control Panel Installation Manual

Page 2

1 2 3 4 5 6 7 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Controlled-products-systems-group 1042011 Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Sécurité Controlled-products-systems-group 1042011