Controlled-products-systems-group 109773 Manuel d'utilisateur télécharger pdf (Page 12)

FORCE:

Adjusts Motor thrust.

= minimum force

= maximum force

OPENING DIRECTION:

Indicates the gate opening movement and

makes it possible not to change the motor

connections on the terminal board.

= Rightward opening movement

= Leftward opening movement

STATUS OF AUTOMATED SYSTEM:

Exit from programming, save data, and return

to gate status viewing.

= Closed

= Now opening

= At "STOP"

= Open

= Pause

= "FAIL SAFE" tripped

= Now closing

= Now reversing

= Photocells tripped

Display Function Default Display Function Default

Display Function Default

5.5.2. ADVANCED PROGRAMMING

To access ADVANCED PROGRAMMING, press key F and, as you hold

it down, press key +:

•if you release key + , the display indicates the name of the first

function.

•if you release key F too, the display shows the value of the

function that can be modified with keys + and -.

•if you press key F (and hold it down), the display shows the

name of the next function, and if you release it, the value that

can be modified with keys + and - is shown.

•when you reach the last function, press F to exit the program,

and the display resumes showing the gate status.

The following table shows the sequence of functions accessible in

ADVANCED PROGRAMMING:

ADVANCED PROGRAMMING

MAXIMUM TORQUE AT INITIAL THRUST:

The motor operate at maximum torque (ignoring

the torque setting) at start of movement. Useful

for heavy leaves.

= Active

= Disabled

FINAL BRAKING:

When the gate engages the opening or

closing limit-switch, a braking stroke can be

selected to ensure the leaf is stopped

immediately. If decelerations are selected,

braking starts when they finish.

At value, braking is disabled.

Time can be adjusted from to in

0.01-second steps.

= Braking disabled

from to = Timed braking

FAIL SAFE:

If this function is activated, it enables a function

test of the photocells before any gate

movement. If the test fails (photocells not

serviceable signalled by value on the

display), the gate does not start moving.

= Active

= Disabled

PRE-FLASHING (5 s):

Activates the flashing lamp for 5 seconds before

start of movement.

= Disabled

= Only before opening

= Only before closing

= Before every movement

CLOSING PHOTOCELLS LOGIC:

Select the tripping mode of the closing

photocells.

They operate for the closing movement only:

they stop movement and reverse it when they

are released, or they reverse it immediately.

= Reverse on release

= Reverse immediately to opening

INDICATOR-LIGHT:

If is selected, the output functions as a

standard indicator-light (lighted at opening

and pause, flashing at closing, and off when

gate closed).

Courtesy light: Different figures correspond

to timed activation of the output, which can

be used (by a relay) to power a courtesy

lamp. Time can be adjusted from to

sec. in 1-second steps, and from to

min. in 10-second steps.

Electric lock command and 'traffic lights'

functions:

If you press key - from the setting, the

command for the closing electric lock is

activated;

If you press - again, the command for the

closing and opening electric lock is set;

if you press the - key again, you can set the

'traffic lights' functions and .

= Standard indicator-light

from to = Timed output.

= electric lock command before opening

movement

= electric lock command before

opening and closing movements

= 'traffic lights' function: the output is

active in "open" and "open on pause" status

and is disabled 3 seconds before the closing

manoeuvre starts.

Note: there is 3 seconds of pre-flashing before

the closing manoeuvre.

= 'traffic lights' function: the output is

active only in "closed" status.

Attention: do not exceed the output's

maximum load (24Vdc-3W). If necessary,

use a relay and a power supply source

outside the equipment.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 18 19

Commentaires sur ces manuels

Pas de commentaire

Controlled-products-systems-group 109773 Manuel d'utilisateur Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Sécurité Controlled-products-systems-group 109773