Controlled-products-systems-group 109773 Manuel d'utilisateur télécharger pdf (Page 2)

1) ATTENTION! To ensure the safety of people, it is important that you read

all the following instructions. Incorrect installation or incorrect use of

the product could cause serious harm to people.

Carefully read the instructions before beginning to install the product.

3) Do not leave packing materials (plastic, polystyrene, etc.) within reach

of children as such materials are potential sources of danger.

4) Store these instructions for future reference.

5) This product was designed and built strictly for the use indicated in this

documentation. Any other use, not expressly indicated here, could

compromise the good condition/operation of the product and/or be a

source of danger.

6) FAAC declines all liability caused by improper use or use other than that

for which the automated system was intended.

7) Do not install the equipment in an explosive atmosphere: the presence

of inflammable gas or fumes is a serious danger to safety.

8) The mechanical parts must conform to the provisions of Standards EN

12604 and EN 12605.

For non-EU countries, to obtain an adequate level of safety, the Standards

mentioned above must be observed, in addition to national legal

regulations.

9) FAAC is not responsible for failure to observe Good Technique in the

construction of the closing elements to be motorised, or for any

deformation that may occur during use.

10) The installation must conform to Standards EN 12453 and EN 12445.

For non-EU countries, to obtain an adequate level of safety, the Standards

mentioned above must be observed, in addition to national legal

regulations.

11) Before attempting any job on the system, cut out electrical power .

12) The mains power supply of the automated system must be fitted with an

all-pole switch with contact opening distance of 3mm or greater. Use

of a 6A thermal breaker with all-pole circuit break is recommended.

13) Make sure that a differential switch with threshold of 0.03 A is fitted

upstream of the system.

14) Make sure that the earthing system is perfectly constructed, and

connect metal parts of the means of the closure to it.

15) The automated system is supplied with an intrinsic anti-crushing safety

device consisting of a torque control. Nevertheless, its tripping

threshold must be checked as specified in the Standards indicated at

point 10.

16) The safety devices (EN 12978 standard) protect any danger areas

against mechanical movement Risks, such as crushing, dragging,

and shearing.

17) Use of at least one indicator-light (e.g. FAACLIGHT ) is recommended

for every system, as well as a warning sign adequately secured to the

frame structure, in addition to the devices mentioned at point “16”.

18) FAAC declines all liability as concerns safety and efficient operation

of the automated system, if system components not produced by

FAAC are used.

19) For maintenance, strictly use original parts by FAAC.

20) Do not in any way modify the components of the automated system.

21) The installer shall supply all information concerning manual operation

of the system in case of an emergency, and shall hand over to the

user the warnings handbook supplied with the product.

22) Do not allow children or adults to stay near the product while it is

operating.

23) Keep remote controls or other pulse generators away from children,

to prevent the automated system from being activated involuntarily.

24)

Transit is permitted only when the automated system is idle.

25) The user must not attempt any kind of repair or direct action whatever

and contact qualified personnel only.

26) Maintenance: check at least every 6 months the efficiency of the

system, particularly the efficiency of the safety devices (including,

where foreseen, the operator thrust force) and of the release devices.

27) Anything not expressly specified in these instructions is not permitted.

WARNINGS FOR THE INSTALLER

GENERAL SAFETY OBLIGATIONS

EC DECLARATION OF CONFORMITY FOR MACHINES

(DIRECTIVE 98/37/EC)

Manufacturer: FAAC S.p.A.

Address: Via Benini, 1 - 40069 Zola Predosa BOLOGNA - ITALY

Declares that: Operator mod. 746ER with electronic control unit 780D

• is built to be integrated into a machine or to be assembled with other machinery to create a machine under the provisions

of Directive 98/37/EC;

• conforms to the essential safety requirements of the following EEC directives:

73/23/EEC and subsequent amendment 93/68/EEC.

89/336/EEC and subsequent amendment 92/31/EEC and 93/68/EEC

and also declares that it is prohibited to put into service the machinery until the machine in which it will be integrated or

of which it will become a component has been identified and declared as conforming to the conditions of Directive 98/

37/EC.

Bologna, 01 January 2004

The Managing Director

A. Bassi

1 2 3 4 5 6 7 ... 18 19

Commentaires sur ces manuels

Pas de commentaire

Controlled-products-systems-group 109773 Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Sécurité Controlled-products-systems-group 109773